Tag Archive for: sampling probe

Posts

Syngas monitoring

May 24, 2016/in Applications, Biogas, Continuous Emissions Monitoring Systems, energy, Portable Analyser, Process Monitoring, renewable /by aymeric

Purpose of gas monitoring in DRI plant

The use of process gas online monitoring systems at locations such blast furnace gas outlet, converter off gas exhaust and coking gas outlet is very reasonable in order to analyse the fuel gases composition by measuring the concentration of CO, CO2, O2, N2, CH4, and H2. There from the calorific value BTU and the Wobbe Index WI can be accurately calculated. Modern steel plants uses dedicated stationary online monitoring system to monitor the primary constituents of Direct Reduction Iron process gases essential to have a full understanding of the process status and efficiency.

In particular, the energy content of the gases, as described by their calorific value, provides the user with important information about efficient firing of different plants in the steel mill (coking plant, sinter plant, rolling mill, etc.) or a nearby power plant.

High-calorific coke or natural gas is mixed with low-calorific converter or blast furnace gas in mixing stations. This is to adjust the calorific value of the mixture to the requirements of the subsequent consumer and to avoid discharging of valuable gases into the off gas.

The knowledge of the calorific value together with information about pressure and flow rate of the fuel gas enables the user to adjust a constant energy content of the mixed gas using an intelligent control system.

Furthermore, analysis data of the gas analysers are also used to determine the equivalent amount of oxygen that is required to run the combustion process. This results in a stoichiometric and uniform combustion and prevents soot production.

Monitoring locations

The number of monitoring points can vary depending of the degree of automation and optimisation desired by the plant operators as well as the type, quality and stability of the combustible used.

Monitoring locations in Syngas Plant often include

Sampling Point Location	Measuring purposes	Measured components	Recommended technology
At the stack of the sinter plant	Monitoring compliance of pollutant emission with existing regulations	CO, SO2, NOx, O2	Laser (OFCEAS), NDIR and/or Electrochemical sensor based Continuous Emissions Monitoring Systems.*
At the raw material storage hall	Monitoring ambient air for toxic gases	CO	NDIR Gas detector
At the raw material silo	Early detection of dangers arising from • Acetylene from calcium carbide • Fire hazard originating from magnesium	C2H2 O2	Laser (OFCEAS), NDIR Gas analyser.*
After blast furnace uptake duct	Optimizing the blast furnace process from blast furnace gas composition	CO, CO2, CH4 H2	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system.*
After dust bags	Early detection of explosion risk for the dust bags from CO contents of the blast furnace gas	CO CO2, CH4 H2	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system.*
At the blast furnace gas outlet	Determination of the calorific value of the blast furnace gas for billing purposes	CO, CO2, CH4 Calorific value H2, N2, O2, CO	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system with Built-in calorific value calculation.Sampling method and measuring principle to be selected based on the exact application requirements.*
At the outlet of coal silo to coal mill	Early detection of smouldering fires	CO CH4	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system.*
At the stack of the coking plant	Monitoring compliance of pollutant emission with existing regulations	CO, NO, SO2, O2 Dust	Laser (OFCEAS), NDIR and Electrochemical sensor based Continuous Emissions Monitoring Systems.* Insitu dust analyser.
At the coal dust silo	Early detection of smouldering fires	CO	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system.*
At the off gas exit of coal mill	Monitoring compliance of dust emission with existing regulations	CO Dust	Laser (OFCEAS), NDIR and Electrochemical sensor based Continuous Emissions Monitoring Systems (heated sampling system required).* Insitu dust analyser.
At the hot blast inlet	Monitoring the oxygen content of the hot blast in order to optimize the blast furnace process	O2	Insitu Combustion analyser type Zirconium with built in metallic reference.
At the stack of the hot blast oven	Monitoring compliance of pollutant emission with existing regulations	CO, NO, SO2, O2 Dust	Laser (OFCEAS), NDIR and Electrochemical sensor based Continuous Emissions Monitoring Systems.* Insitu dust analyser.
At the converter off gas outlet	Optimizing the converter process from the composition of the converter off gas	CO, CO2, O2 CO, CO2, H2	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system.*
At the coking gas outlet	Determination of the calorific value of the coke oven gas for billing purposes and early detection of explosion risk	CO, CH4, O2 H2 Calorific value	Laser (OFCEAS), NDIR and/or Electrochemical sensor based online gas monitoring system with Built-in calorific value calculation.*

(*) Sampling method and measuring principle to be selected based on the exact application requirements and specifications.

Syngas online monitoring systems

The use of advanced online monitoring systems installed in the heart of syngas processes usually requires integration into air conditioned analyser rooms or shelters to preserve the instruments from harsh plant conditions and corrosive atmospheres. The installation in an area protected from the weather also secures the data/instrument availability by providing permanent access to the analysers – if attendance is required for maintenance or diagnosis.

Systems certified for installation in explosive area (ATEX) may be required in some cases.

Reliable, accurate and application customised online monitoring systems are valuable in DRI and other syngas plants as they allow determining the quality parameters of blast furnace, coke and natural gas essential to process optimisation.

AquaGas Pty Ltd offers a broad range of portable and stationary monitoring systems specifically designed to handle syngas online monitoring requirements.

Our analysers and systems provide plant operator with application specific key features:

Simultaneous measurement of several components within the same instruments reducing the cost of the system itself but also easing integration, installation and operation tasks
Combine various cells and measurement principles into the same instrument
Measure accurately over a large dynamic range
Measure all primary constituents of process gas: CO, CH4, O2, H2, CO, CO2, H2, CnHm
Calculate automatically the gas calorific value BTU and Wobbe Index WI
Allow fast sample transfer on long distances
Maintain the gas temperature above dew point
Decrease and stabilize the sample dew point prior analysis to eliminate water vapour cross interferences
Transmit to the plant DCS individual readings for all measured components (analogue or serial communication)
Convey the sample in SS, PFA or PFTE gas path
Designed to operate in harsh conditions
Remove particulates, soot and tar from the sample directly at the sampling location
Automatic sampling and calibration sequences including span, zero check, system purge, probe backflush
Store internally at least one month of data
Dedicated sampling system featuring heated particulate filtration and sample transfer, high temperature sampling probe, Gas cooler with PFA coated heat exchanger or Nafion membrane drier.

Monitoring solutions tailored to the needs of syngas plants

: Low Cost multigas CEMS

: Online Syngas Multigas analyser

: Portable Gas Sampling system

: Portable Gas Analyser

: Portable Gas Analyser

: Gas Sampling Probe

: Hand held Analyser

: Stationary sampling system – CEMS

: Portable Gas Analyser

: ABYSS NDIR Syngas Analyser

AquaGas is supporting the global industrial community with high performance environmental and process monitoring systems (Continuous Emissions Monitoring Systems, Air Quality Monitoring Systems, Online process analysers, Water Quality Monitoring Systems) specifically designed and built to meet your application requirements.

1 2 3 4

ATEX Syngas Monitoring Systems

Process gas online monitoring

Environmental Data acquisition and reporting software

Water Quality Monitoring Systems

CEMS and process gas analyser

May 12, 2016/in Air Quality, anaerobic digestion/bacteria, Applications, Biogas, CEMS, Continuous Emissions Monitoring Systems, Direct Extractive, energy, fermentation process, Gas coolers, landfill, Methanation, Multipoint Monitoring, NDIR, News, Portable Analyser, Power Station, Process Monitoring, processed biomethane, raw biogas, renewable, Sampling system, stack emissions, waste incinerator, waste-to-energy /by aymeric

A new approach to continuous gas monitoring

The Mamos is a high quality stationary monitoring system for the measurement of up to 6 gases as well as gas temperature, ambiant and differential pressures (Gas Flow) in a large field of applications.

Designed to optimise performance/price ratio, small in size and yet very skilful analyser, the Mamos is the field proven alternative for large, intricate Continuous Emissions Monitoring Systems, as it does not fall behind them concerning functionality, abilities, reliability and is far ahead in terms of expenses.

Online monitoring made easy

Fully automated and packed with exclusive features, the Mamos concept enlarges monitoring possibilities and respond to the today’s demands in terms of accuracy, reliability and flexibility. Each analyser is supplied with its own sampling system. The entire system is mounted on a wall mount plate and designed for installation in industrial settings and rough environment. It has a modular construction, and offer a large panel of add-ons to match site specific application requirements. The Mamos minimises the installation and ongoing operation cost until now required to fulfil your monitoring needs.

Multigas

Depending of the gas matrix and components to be analysed, the Mamos can be fitted with up to 6 different sensors. The combination of technologies (NDIR, TCD, PID, Electrochemical) and the addition of separate gas channels into the same instrument empower flexibility in multigas applications. A unique feature is to allocate a gas channel to sensible sensors. Its design ensures the cells have a limited exposure to gases and therefore extends considerably their respective life-time.

Process gas and emissions monitoring in combustion plants, boilers, syngas, biogas, waste recycling facilities and associated filtration systems are typical applications for multiple gas channels configuration.

In Biogas, the primary gas channel holds the CO₂, CH₄, O₂sensors while an additional separate gas channel is allocated to sensible Electrochemical sensors, H2S for example. The two NDIR gas channels can then be used for CO and VOCs.

The Mamos offers multiple sensor and method configurations. Here are the measuring parameter for the most common gases. For other gases or different measuring ranges (MR), please consult us.

Gas & MR

Gas	Analysis Method	Range I Resolution	Accuracy	Time (T90)	Conformity
O₂ Oxygen	Electrochemical, Partial Pressure	20.95% \| 0.01%	± 0.1% abs. or 5% rel.	45 sec	ISO 12039, CTM-030
O₂ Oxygen	Electrochemical, Partial Pressure	25.00% \| 0.01%	± 0.1% abs. or 5% rel.	45 sec	ISO 12039, CTM-030
O₂ Oxygen	Electrochemical, Partial Pressure	100.00% \| 0.01%	± 0.1% abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	Electrochemical Sensor	4 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	Electrochemical, with H2 compensation	4 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	Electrochemical Sensor	20 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	Electrochemical, with H2 compensation	20 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	Electrochemical Sensor	10% \| 0.001%	± 0.005% abs. or 5% rel.	45 sec	ISO 12039, CTM-030
CO Carbon Monoxide	NDIR Non Dispersive Infra Red	10% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	EN 15058 and Method 10
CO Carbon Monoxide	NDIR Non Dispersive Infra Red	25% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	EN 15058 and Method 10
CO Carbon Monoxide	NDIR Non Dispersive Infra Red	50% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	EN 15058 and Method 10
CO Carbon Monoxide	NDIR Non Dispersive Infra Red	100% \| 0.1%	± 0.5% abs. or 5% rel.	45 sec	EN 15058 and Method 10
CO₂ Carbon Dioxide	NDIR Non Dispersive Infra Red	5% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	ISO 12039, OTM-13
CO₂ Carbon Dioxide	NDIR Non Dispersive Infra Red	10% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	ISO 12039, OTM-13
CO₂ Carbon Dioxide	NDIR Non Dispersive Infra Red	25% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	ISO 12039, OTM-13
CO₂ Carbon Dioxide	NDIR Non Dispersive Infra Red	50% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec	ISO 12039, OTM-13
CO₂ Carbon Dioxide	NDIR Non Dispersive Infra Red	100% \| 0.1%	± 0.5% abs. or 5% rel.	45 sec	ISO 12039, OTM-13
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	1% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	5% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	10% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	25% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	50% \| 0.01%	± 0.05% abs. or 5% rel.	45 sec
C_xH_y Total Hydrocarbons	NDIR Non Dispersive Infra Red	100% \| 0.1%	± 0.5% abs. or 5% rel.	45 sec
NO Nitric Oxide	Electrochemical Sensor	1 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	CTM-022
NO Nitric Oxide	Electrochemical Sensor	5 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec	CTM-022
NO₂ Nitrogen Dioxide	Electrochemical Sensor	1 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	60 sec	CTM-022
NO₂ Nitrogen Dioxide	Electrochemical Sensor	4 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	60 sec	CTM-022
SO₂ Sulphur Dioxide	Electrochemical Sensor	2 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec
SO₂ Sulphur Dioxide	Electrochemical Sensor	5 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec
H₂S Hydrogen sulfide	Electrochemical Sensor	1 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	70 sec
H₂S Hydrogen sulfide	Electrochemical Sensor	10 000ppm \| 1ppm	± 5ppm abs. or 5% rel.	45 sec
H₂ Hydrogen	Electrochemical Sensor	2 000ppm \| 1ppm	± 10ppm abs. or 5% rel.	50 sec
H₂ Hydrogen	Electrochemical Sensor	20 000ppm \| 1ppm	± 10ppm abs. or 5% rel.	70 sec
H₂ Hydrogen	TCD Thermal Conductivity Detector	10% \| 0.1%	± 0.5% abs. or 5% rel	45 sec
H₂ Hydrogen	TCD Thermal Conductivity Detector	25% \| 0.1%	± 0.5% abs. or 5% rel	45 sec
H₂ Hydrogen	TCD Thermal Conductivity Detector	50% \| 0.1%	± 0.5% abs. or 5% rel	45 sec
H₂ Hydrogen	TCD Thermal Conductivity Detector	100% \| 0.1%	± 0.5% abs. or 5% rel	45 sec
N₂O Nitrous Oxide	NDIR Non Dispersive Infra Red	2 000ppm \| 1ppm	± 10ppm abs. or 5% rel	45 sec	ISO 21258
N₂O Nitrous Oxide	NDIR Non Dispersive Infra Red	5 000ppm \| 1ppm	± 10ppm abs. or 5% rel	45 sec	ISO 21258
CHF₃ Fluoroform (Refrigerant R23)	NDIR Non Dispersive Infra Red	2.5% \| 0.01%	± 0.05 abs. or 5% rel.	45 sec
CL₂ Chlorine	Electrochemical Sensor	250ppm \| 1ppm	± 5ppm abs. or 5% rel.	60 sec
VOC Volatile Organic Compounds	PID Photo Ionization Detector	100ppm \| 1ppm	± 5ppm abs. or 5% rel.	120 sec	Method 21
VOC Volatile Organic Compounds	PID Photo Ionization Detector	1000ppm \| 1ppm	± 5ppm abs. or 5% rel.	120 sec	Method 21

Pleasant interface

Its powerful and pleasant PC interface provides operators and system integrators with a broad range of settings to adjust many aspects of the measurement tasks such as automated sampling, calibration, purge sequences, analogue outputs behaviour, data presentations…

For large sites with complex monitoring requirements, the LAN and ModBus interfaces allow implementing in an efficient way large instruments networks with master/slave configurations and user settable monitoring functions.

Optimised integration

This compact system is delivered ready for installation. Thanks to its small size, the system is easy to locate, install and set-up. The routing of the cables and tubes to the instrument is simplified with all gas and electrical connections grouped onto a single plate.

Advanced Features

Miniature and field replaceable technology

Standard configuration includes 6 sensors (NDIR, TCD, PID or Electrochemical)

Measured gases: O2, CO, CO2, CxHy, NO, NO2, SO2, H2S, H2, N2O, Cl2, VOC

Built-in real-time calculations for the following process parameters:

Process Parameters

Variable	Method	Range I Resolution	Accuracy	Response Time (T90)
T_gas Gas temperature	K-type thermocouple	-50 ÷ 1000°C \| 0.1°C	± 2°C	10 sec
T_gas Gas temperature	S-type thermocouple	-50 ÷ 1000°C \| 0.1°C	± 2°C	10 sec
T_amb Boiler intake air temperature	PT500 resistive sensor	-50 ÷ 1000°C \| 0.1°C	± 2°C	10 sec
DP Differential Pressure	Silicon piezo-resistive pressure sensor	25hPa ÷ +25hPa \| 1Pa (0.01hPa)	± 2Pa abs. or 5% rel.	10 sec
V Gas velocity	With sampling probe equipped Pitot tube & pressure sensor	1 ÷ 50m/s \| 0.1m/s	0.3m/s abs. or 5% rel.	10 sec
Lambda λ Excess air number	Calculated	1 ÷ 10 \| 0.01	± 5% rel.	10 sec
qA Stack loss	Calculated	0 ÷ 100% \| 0.1%	± 5% rel	10 sec
Eta η Combustion Efficiency	Calculated	0 ÷ 120% \| 0.1%	± 5% rel	10 sec

Large display / User friendly menu

Built-in gas chiller with continuous condensate removal

Data-logger with SD card for results collection.

Analogue outputs (both current and voltage) to control external devices

User configurable functions controlled via digital and analogue inputs

USB, LAN, RS485 and MODBUS

Versatile in use

The sampling system configuration can be adapted to specific monitoring needs such as multipoint monitoring, redundancy, continuous or time set measuring cycles… When sampling from wet and hot gas, moisture content, condensates and salts are continuously removed by the use of one or several gas dryer(s) (Peltier or Nafion) equipped with built-in safety filter, condensate trap and safety inline particulate filters.

Wether it uses the built-in sampling pump or the pressure from the source, the analyser is designed to work with overpressure. Single gas channel configuration can handle overpressure up 1.8 bar.

MD3 for high moisture content – Waste incinerator, Syngas, Coal Power Stations, Chemical and refinery facilities, (…)

MD2 for low and medium moisture content – Biogas, landfill, odour filtration system, LNG, (…)

Three configurations

Compact – Short-extractive CEMS – Analyser with gas dryer on a common mounting plate, all installed near the measurement place.

Specifications

Dimensions (W x H x D)	240 mm x 360 mm x 160 mm
Weight (depends on equipment)	4 kg ÷ 5 kg
Casing’s material	ABS
Protection grade	IP 20
Mounting plate dimensions (H x W) \| material \| weight	596 mm x 450 mm \| aluminium \| 1.9 kg
Operating conditions	T: 10°C ÷ 50°C, RH: 5% ÷ 90% (non-condensing)
Storing temperature	0°C ÷ 55°C
Power consumption (analyser unit only)	30 W max
Data-logger: type \| size \| number of results	SD flash card \| max 4GB \| practically unlimited
Display: type \| parameters	Backlit LCD \| 20 characters x 4 lines
Gas pump: type \| max gas flow \| standard gas flow	Diaphragm \| max 2l/min \| 1.5l/min (90l/h)
Maximal extraction point pressure:	Atmospheric ±200hPa
Current analogue outputs	4 outputs 0mA ÷ 20mA or 4mA ÷ 20mA
Voltage analogue outputs	4 outputs 0V ÷ 5V or 0V ÷ 10V
Digital inputs	2 inputs, TTL levels, floating = high level
Digital outputs	1 open collector output + 2 SPDT relays (optional)
Computer communication interface	B type USB socket

Split /1 dryer – Cold Dry Extractive CEMS – Analyser and gas dryer are installed on separate mounting plates, each equipped with its own power supply module. The gas dryer is installed near the sampling point therefore the analyser can be located away from the source. Once free from water vapour, the sample can be conveyed on long distances without the need for heated lines.

Split/2 dryers – Cold Dry Extractive CEMS – Compact configuration with an additional gas dryer installed on separate mounting plates, each equipped with its own power supply module. Two dryers in serial for high drying performances suitable for Traces monitoring in wet sample.

Twin Split – Cold Dry Multipoint CEMS – This version is based on the Twin Split/1 dryer configuration, but uses two MD3 dryer with their own power supply added on separate mounting plates enabling measurements from two different locations (each dryer is installed near the sampling point). User programmable sampling sequences.

Download Brochure

Madur, state-of-the-art monitoring solutions

: Low Cost multigas CEMS

: Hand held Analyser

: PGD100 – Gas Conditionner

: GA21plus – Portable Gas Analyser

: Stationary Gas Sampling Probes

: Portable Gas Analyser

: Portable Gas Analyser

: GA12 – Handheld Analyser

: Portable Gas Analyser

: PhotonS – Stationary CEMS

: MD3 Gas dryer

1300 850 862

Call us with your application details handy to organise a CEMS demo at your facilities !

1 2 3 4

Continuous Emissions Monitoring Systems

Process gas online monitoring

Combustion analysers

Water Quality Monitoring Systems

Universal gas sampling system

March 10, 2016/in Applications, Biogas, CEMS, Continuous Emissions Monitoring Systems, Direct Extractive, energy, Gas coolers, landfill, News, Process Monitoring, renewable, Sampling system, stack emissions, waste incinerator, waste-to-energy /by aymeric

Sampling is a key factor to ensure representative analysis and essential to preserve the good status of your monitoring system. AquaGas Monitoring Systems introduces Ankersmid Sampling BVBA (Belgium) stationary sampling equipment designed for Continuous Emission Monitoring (CEMS) and process online analysis.

AquaGas solutions are available as system components for integration into third party systems or as complete turn-key systems. Our systems combine the best technologies available to extract, transfer, and condition samples from stack or crucial process locations prior to analysis.

Ankersmid Sampling Patented design offers a wide selection of modular options and combinations essential to optimise sampling performances and secure the availability rate of CEMS and process monitoring equipment.

Our adaptative product range is versatile and suits a large variety of applications including:

Cement Plant
Power Station (Coal fired, Diesel…)
Waste Incinerators
DeNOx, deSOx and other flue gas treatment process
Combustion and Process control
Syngas and biogas plant
Refineries…

Heated Gas Sample Probes

50°C to 320°C with PID controller or 0-180°C self-limiting heating cartridges
High & Low temperature alarm and RS485 ModBus
Wide variety of filter materials, length and porosity
PTFE demister for wet scrubbers
Blowback function for higher dust load up to 10g/Nm3
The test gas injection port according to emissions standards (EN14181)
Calibration gas feeding via the filter element of the gas sample probe
Large selection of heated and unheated sample tubes (incl. ATEX)
Easy access to filter, inner stack sample tube, and top-filter
Efficient and fast maintenance and routine inspection tasks

ASP Series

Heated Lines

50°C to 200°C Heated Line with PID controller
0-180°C self-limiting heat trace Sample line
High & Low temperature alarm and RS485 ModBus
Large choice of options and combinations (incl. ATEX)
PTFE or SS316 inner tube
Multiple inner tubes for calibration, air and sample flows
No cold spot
Large selection of temperature sensor
UV rated PA12 , Polyamide braiding or highly flexible smooth silicon outer jacket
Maintenance free and delivered ready for installation

AHL Heated Lines

Gas Conditioners

4°C +/-0.1°C dew point stabiliser
19 inch rack or wall mount units
High & Low temperature alarm and RS485 ModBus
Large choice of options and combinations (incl. ATEX)
Ankersmid Sampling patented NEO® heat exchanger design
Multiple stream capabilities
PFA® coated gas path and heat exchanger
ASS integrated rack mount complete stationary sampling system
Low maintenance and reduced operating cost
High-performance continuous condensate purge
AOX, TUV certified 99% conversion efficiency NOx converter

Gas Conditionners

Gas Sampling Pumps

High performance PTFE gas sampling pump
5 to 30 lpm flow range
5 to 240°C operating temperature range
Designed for a large range of analytical applications (incl. ATEX)
Large choice of options and combinations

Speciality Filters

Universal all purposes filters
Deep acting particulate filters
Calibration gas humidifiers
Scrubbers and adsorption material
Liquid stop, condensate drain…
Built-in liquid alarm sensor, condensate purge, heater…

CEMS components

Universal
CEMS integration made easy
Performant
Field proven, high quality, durable Ankersmid Sampling BVBA patented designs
Modular
Comprehensive range of gas sampling equipment from one source
Efficient
Easy to install, maintain and operate

Brochure

1 2 3 4

Posts

Purpose of gas monitoring in DRI plant

Monitoring locations

Monitoring locations in Syngas Plant often include

Syngas online monitoring systems

AquaGas Pty Ltd offers a broad range of portable and stationary monitoring systems specifically designed to handle syngas online monitoring requirements.

Monitoring solutions tailored to the needs of syngas plants

A new approach to continuous gas monitoring

Online monitoring made easy

Multigas

Pleasant interface

Optimised integration

Advanced Features

Versatile in use

Three configurations

Madur, state-of-the-art monitoring solutions

Call us with your application details handy to organise a CEMS demo at your facilities !

Heated Gas Sample Probes

Heated Lines

Gas Conditioners

Gas Sampling Pumps

Speciality Filters

SERVICES & PRODUCTS ENQUIRIES

PRODUCTS

PARTNERS

APPLICATIONS